INSTALLATION INSTRUCTIONSVinyl Railing and Stair RailingFor Traditional and Williamsburg Styles34107310BOMRead all instructions prior to installing pr
10Attach each 2" top rail bracket with four #10 x 2" square drive screws (Fig. 6). Attach each bottom rail bracket with four #10 x 11⁄1⁄12⁄2
11What is covered: Barrette Outdoor Living warrants vinyl and aluminum products to include; vinyl and aluminum fence, vinyl and aluminum railing and p
12
INSTRUCCIONES DE INSTALACIÓNBarandal de vinilo y barandal de escalerasPara los estilos Traditional y Williamsburg34107310BOMLea todas las instruccione
14Cinta métricaNivelTaladroBrocas de 5⁄5⁄532⁄32⁄" y 1⁄1⁄18⁄8⁄"Dado cuadrado #2Bloques de madera de 7.6 cmSeguetaAbrazaderasGafas de protecci
15Ensamblado del tramo de barandal:Las lengüetas de cierre automático en los barrotes o pilares deben estar orientadas hacia el borde exterior de los
16Fig. 6Deslice el tramo de travesaño entre los postes y encima de los bloques espaciadores temporales de madera (coloque los bloques junto a los post
17Cubiertas de soporte superior:a. Asegúrese de que el barandal esté centrado entre los dos postes y apriete los tornillos de ajuste en los soportes
18BARANDAL DE ESCALERA DE VINILOColoque el tramo de barandal de escalera ensamblado junto a los postes de escalera ya instalados (Fig. 1). Mida la dis
19Retire las pinzas del kit de escalera de los postes. Corte a lo largo de las cuatro marcas en ángulo en los travesaños (Fig. 5).Deslice los soportes
2Tape MeasureLevelDrill5⁄5⁄532⁄32⁄" and 1⁄1⁄18⁄8⁄" Drill Bits#2 Square Drive Bit3" Wood BlocksHacksawClampsSafety GlassesTOOLS NEEDED:B
20Marque todos los agujeros del soporte (Fig. 8). Taladre los agujeros del soportes con una broca de 1⁄1⁄18⁄8⁄" (Fig. 9). Instale los tornillos
21Después de instalar los postes, determine el ángulo y la altura del baranda (Fig. 1).Taladre ori cios de 1⁄1⁄18⁄8⁄" de diámetro en la base del
22Fije cada soporte de travesaño superior de 2" con cuatro tornillos cuadrados #10 de 2" (Fig. 6). Fije cada soporte de travesaño inferior c
23Cuál es su cobertura: Barrette Outdoor Living garantiza los productos de vinilo y aluminio, que incluyen vallas de vinilo y aluminio, travesaños de
BARRETTE OUTDOOR LIVING7830 FREEWAY CIRCLEMIDDLEBURG HEIGHTS, OHIO 44130TEL: (800) 336-2383WWW.VERANDA.BARRETTEOUTDOORLIVING.COM
3Assembling rail section: Lock tabs on balusters/spindles must face outer edge of routed holes in rails. Assemble your rail section by snapping balust
4Fig. 6Slide rail section in-between posts and on top of temporary spacer blocks (position spacer blocks next to installed vinyl posts) (Fig. 6).6For
5Top Bracket Covers:a. Ensure the railing is centered between both posts and tighten the set screws put into the metal brackets from Step 4.b. Open
6VINYL STAIR RAILINGPlace assembled stair rail section adjacent to the mounted stair posts (Fig. 1). Measure the distance from the rst and last balu
7Remove clamped stair kit from posts. Cut along all four angled marks on rails (Fig. 5).Slide the angle brackets onto the rails (Fig. 6), and place ra
8Mark all bracket holes (Fig. 8). Predrill all bracket holes with 1⁄1⁄18⁄8⁄" drill bit (Fig. 9).Drive screws through brackets into post (Fig. 10)
9After posts have been installed, determine angle and height of railing (Fig. 1).Pre-drill 1⁄1⁄18⁄8⁄" diameter holes in base of top bracket only.
Comments to this Manuals