Veranda 181980 Instruction Manual

Browse online or download Instruction Manual for Unknown Veranda 181980. Veranda 181980 Instructions / Assembly User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
3'X42" SPACED PICKET GATE
ASSEMBLY INSTRUCTIONS AND INSTALLATION TIPS
Continue to push the picket through the bottom rail into the throat and
hole of the second rail (fig. 3). The second rail becomes the top rail of
the assembly. Stop when the tab in the bottom rail and the notch on
the picket align. DO NOT SNAP INTO PLACE.
Continue this process until all pickets are inserted into the rails with the
tabs and notches aligned (fig. 4).
Once all the pickets are in place, snap the rails into all the picket
notches using your hands or gently tap with a rubber mallet (g. 5).
Items you may need:
Step 1
Soapy water
Non-marring rubber mallet
Wooden wedge
Power drill
1/4" drill bit
7/16" wrench
• Shims
Step 2
Step 3
NOTE: PicketLock
is a patent-pending technology that provides a
glue- and fastener-free connection between the pickets and rails.
You may spray soapy water onto components to help them slide more
easily into their corresponding channels. A non-marring rubber mallet
may also be used to gently tap components more firmly into place.
PLANNING: Prior to construction, check with your local regulatory
agency for special code requirements in your area. Contact your
utility supplier to locate and mark underground lines.
Careful planning and measuring of your fence project is essential,
as moving posts after the concrete sets is extremely difcult.
Take one of the rails and gently open up the throat with your hand or a
wooden wedge (fig. 1). This will become the bottom rail of the assembly.
Insert a picket into the throat of the rail, and proceed through the
routered hole as shown. DO NOT SNAP INTO PLACE (fig. 2).
Actual size: 34"h x 41-1/2"w
fig. 1 fig. 2
fig. 3 fig. 4
Place gate jambs on both sides of the rails and place the hinges on
the gate jamb so they are aligned with the rails. Using the bracket as
a guide, drill the three (3) necessary 1/4" holes for the bracket bolts.
Repeat these steps for the hinged brackets as well (fig. 6). Ensure the
rails are fully inserted in the jamb before drilling. The bolts need to go
through the jamb and rail to function properly.
Slide the hinged bracket and bracket on the top and bottom of the gate
jambs. Attach hinges to jambs with the supplied through bolts. Connect
bolts with the supplied cap nuts. Ensure the gate is square before all
bolts are tight. When square, tighten all bolts with a 7/16" wrench.
Step 4
fig. 6
fig. 5
Page view 0
1 2 3 4

Summary of Contents

Page 1 - Items you may need:

3'X42" SPACED PICKET GATEASSEMBLY INSTRUCTIONS AND INSTALLATION TIPSContinue to push the picket through the bottom rail into the throat and

Page 2 - Digging Post Holes

Measure to be sure you can install the gate to the post with approximately a 2" gap from the ground to the bottom of the gate. Align the rails on

Page 3

PUERTA CON ESTACAS ESPACIADAS DE 3'X42"INSTRUCCIONES DE MONTAJE Y CONSEJOS DE INSTALACIÓNContinúe empujando la estaca a través del barandal

Page 4 - Instalación de la puerta

Mida para asegurarse de que puede instalar la puerta al poste con una brecha de aproximadamente 2" desde el suelo hasta la parte inferior de la p

Comments to this Manuals

No comments