Veranda 181985 Instruction Manual download pdf

4'X42" SPADED SCALLOPED PICKET GATE

ASSEMBLY INSTRUCTIONS AND INSTALLATION TIPS

Continue to push the picket through the bottom rail into the throat and

hole of the second rail (ﬁg. 3). The second rail becomes the top rail of

the assembly. Stop when the tab in the bottom rail and the notch on

the picket align. DO NOT SNAP INTO PLACE.

Continue this process until all pickets are inserted into the rails with the

tabs and notches aligned (ﬁg. 4).

Once all the pickets are in place, snap the rails into all the picket

notches using your hands or gently tap with a rubber mallet (ﬁg. 5).

Step 1

Step 2

Step 3

NOTE: PicketLock

™

is a patent-pending technology that provides a

glue- and fastener-free connection between the pickets and rails. You

may spray soapy water onto components to help them slide more

easily into their corresponding channels. A non-marring rubber mallet

may also be used to gently tap components more ﬁrmly into place.

PLANNING:

Prior to construction, check with your local regulatory

agency for special code requirements in your area. Contact your

utility supplier to locate and mark underground lines.

Careful planning and measuring of your fence project is essential, as

moving posts after the concrete sets is extremely difﬁcult.

To ensure the scallop is correct, arrange all of the pickets in order

according to the drawing above before you begin panel assembly.

You will assemble the panel by starting with one of the longest pickets at

either end of your picket arrangement, working toward the opposite end.

Take one of the rails and gently open up the throat with your hand or a

wooden wedge (ﬁg. 1). This will become the bottom rail of the assembly.

Insert a picket into the throat of the rail and proceed through the

routered hole as shown. DO NOT SNAP INTO PLACE (ﬁg. 2).

Actual size: 46"h x 41-1/2"w

Place gate jambs on both sides of the rails and place the hinges on

the gate jamb so they are aligned with the rails. Using the bracket as

a guide, drill the three (3) necessary 1/4" holes for the bracket bolts.

Repeat these steps for the hinged brackets as well (ﬁg. 6). Ensure the

rails are fully inserted in the jamb before drilling. The bolts need to go

through the jamb and rail to function properly.

Slide the hinged bracket and bracket on the top and bottom of the gate

jambs. Attach hinges to jambs with the supplied through bolts. Connect

bolts with the supplied cap nuts. Ensure the gate is square before all

bolts are tight. When square, tighten all bolts with a 7/16" wrench.

Step 4

ﬁg. 6

Items you may need:

• Soapy water

• Non-marring rubber mallet

• Wooden wedge

• Power drill

• 1/4" drill bit

• 7/16" wrench

• Shims

ﬁg. 1 ﬁg. 2

ﬁg. 3 ﬁg. 4

ﬁg. 5

1 2 3 4

Summary of Contents

Page 1 - Items you may need:

4'X42" SPADED SCALLOPED PICKET GATEASSEMBLY INSTRUCTIONS AND INSTALLATION TIPSContinue to push the picket through the bottom rail into the t

Page 2 - Digging Post Holes

Measure to be sure you can install the gate to the post with approximately a 2" gap from the ground to the bottom of the gate. Align the rails on

Page 3

PUERTA CON ESTACAS DE PUNTA DE PICA FESTONEADAS ESPACIADAS 4'X42"INSTRUCCIONES DE MONTAJE Y CONSEJOS DE INSTALACIÓNContinúe empujando la est

Page 4 - Instalación de la puerta

Mida para asegurarse de que puede instalar la puerta al poste con una brecha de aproximadamente 2" desde el suelo hasta la parte inferior de la

Comments to this Manuals

No comments

Veranda 181985 Instruction Manual

Browse online or download Instruction Manual for Unknown Veranda 181985. Veranda 181985 Instructions / Assembly User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Veranda 181985